The Air Lift pumping system is a pump that has low suction and moderate discharge of liquid and entrained solids. The pump injects compressed air at the bottom of the discharge pipe which is immersed in the liquid. The compressed air mixes with the liquid causing the air-water mixture to be less dense than the rest of the liquid around it and therefore is displaced upwards through the discharge pipe by the surrounding liquid of higher density. Solids may be entrained in the flow and if small enough to fit through the pipe, will be discharged with the rest of the flow at a shallower depth or above the surface.
Bailers
Flat Valve Bailers are used to remove cuttings from the hole. When the bailer is lowered into the hole the Flat valve opens to permit the intake of water and cuttings. The bailer is then surfaced and set down to release the contents.
Casing Scraper
The Casing Scraper incorporates blades assembly and is used to remove scale and debris from the internal surface of a casing string. Generally run on tubing or drill pipe, casing scrapers are routinely used during workover operations to ensure that the wellbore is clean before reinstalling the completion string.
Casing Swage
Casing Swages are an economical method of repairing collapsed casing. The swage can also be used as drift prior to running production tools to ensure no restriction down hole. The swage has a shallow taper on the bottom end to allow for efficient swagging and a taper on the top for easy entry into tight spots on the return trip.
Rock bits
Manufactured with superior quality steel, advanced technologies, designed for use with compressed air or fluid circulation systems. Regular and Jet circulation available. Cutting structures allow optimum penetration rates and long runs even in the most difficult and abrasive formations. Weight on the bit is distributed through a five part anti-friction bearing matched and ground with precision to tolerances of ± 0,0002″. Critical areas on the external portion of the bit are protected with tunsten carbide alloy hardfacing.
Soft
Medium – Soft
Medium – Hard
Hard formations
DIAMETER
CONN.
WEIGHT
TOOTH
INSERT
in.
mm.
PIN SIZE
KG
T3
T2
T1H
SE54
SE56
SE58
2 7/8 – 2 15/16
73-75
N-ROD (4 thd)
1.8
□
□
□
□
□
□
3 – 3 1/2
76-89
N-ROD (4 thd)
2
□
□
□
□
□
□
3 3/4 – 3 7/8
95-98
2 3/8 API REG.
4
□
□
□
□
□
□
4 – 4 1/8
101-105
2 3/8 API REG.
5
□
□
□
□
□
□
4 1/4 – 4 1/2
108-114
2 3/8 API REG.
5
□
□
□
□
□
□
4 3/4 – 5″
120-127
2 7/8 API REG.
5.5
□
□
□
□
□
□
5 1/8 – 5 1/2
130-140
2 7/8 API REG.
7
□
□
□
□
□
□
5 7/8
149
3 1/2 API REG.
11.5
■
■
■
■
■
■
6 – 6 1/8
152-155
3 1/2 API REG.
12.6
■
■
■
■
■
■
6 1/4 – 6 1/2
159-165
3 1/2 API REG.
18
■
■
■
■
■
■
6 3/4
171
3 1/2 API REG.
18
■
■
■
■
■
■
7 7/8
200
4 1/2 API REG.
34
■
■
■
■
■
■
8 1/2
216
4 1/2 API REG.
38
■
■
■
■
■
■
When drilling hard and abrasive formations with tooth type rock bits, an excessive wear of the teeth may occur. It is necessary in such cases to use tungsten carbide insert rock bits. A specified in the next table of drilling parameters, more weight must be given when drilling with T.C.I. rock bits in order to obtain a major compression effect on hard rock being drilled.
ROCK BIT TYPE
FORMATION TO DRILL
WEIGHT PER INCH (KG)
SPEED
MIN
MAX
MIN
MAX
TOOTH TYPE ROCK BIT
SOFT – MEDIUM
450
1300
60
110
MEDIUM HARD
450
1800
50
100
DURE – MOLTO DURE
900
2200
40
80
INSERT ROCK BIT
SOFT – MEDIUM
450
1800
45
80
MEDIUM HARD
1200
2800
40
80
HARD AND ABRASIVE
1800
3100
30
60
Large Diameters New & Retiped,Rerun
For oil and water well drilling. New and reconditioned of major U.S.A. brands: HUGHES, SMITH, REED, SECURITY.
milled steel tooth type
tungsten carbide insert type
Available with sealed or regular bearing, with regular or jet circulation.
DIAMETER inch
DIAMETER mm.
CONNECTION
WEIGHT
LBS
KG
5 7/8″
149.2
3 1/2″ API REG. PIN
29
13
6″
152.4
3 1/2″ API REG. PIN
32
14
6 1/8″
155.6
3 1/2″ API REG. PIN
33
14.5
6 1/4″
158.8
3 1/2″ API REG. PIN
40
18
6 1/2″
165.1
3 1/2″ API REG. PIN
46
21
6 3/4″
171.5
3 1/2″ API REG. PIN
49
22
7 7/8″
200.0
4 1/2″ API REG. PIN
76
34
8 1/2″
216.0
4 1/2″ API REG. PIN
90
41
8 3/4″
222.3
4 1/2″ API REG. PIN
92
42
9 1/2″ – 9 7/8″
241.3 – 250.8
6 5/8″ API REG. PIN
141
65
10 5/8″
270.0
6 5/8″ API REG. PIN
170
77
11″
279.4
6 5/8″ API REG. PIN
175
80
12 1/4″
311.2
6 5/8″ API REG. PIN
220
100
13 1/2″ – 13 3/4″
342.9 – 349.3
6 5/8″ API REG. PIN
237
108
14 3/4″
374.7
6 5/8″ o 7 5/8″ API REG. PIN
305
138
16″
406.4
6 5/8″ o 7 5/8″ API REG. PIN
415
187
17 1/2″
444.5
7 5/8″ API REG. PIN
580
262
22″
558.8
7 5/8″ API REG. PIN
766
347
23″
584.2
7 5/8″ API REG. PIN
820
372
26″
660.4
7 5/8″ API REG. PIN
1335
605
28″
711.2
8 5/8″ API REG. PIN
1600
720
Available with sealed or regular bearing , with regulator or jet circulation.
Classification – code IADC
Tooth Type
Soft formations Bits that feature long, widely spaced teeth, to drill soft formation such as shales, soft sandstone, clay and all unconsolidated formations.
IADC CODES 111 – 126 – 134
Tricono a Denti IADC 111
Medium formations With medium length teeth, closer spaces, to drill unconsolidated limestones, medium sandstones, clay, marls
IADC CODES 211 – 224 – 234
Tricono a Denti IADC 211
Medium Hard – Hard formations With short, closely spaced teeth with tungsten carbide hardfacing, for hard and abrasive formations such as sandstones, dolomite, hard limestone and granite.
IADC CODES 311 – 314 – 321
Tricono a Denti IADC 311
Insert Type
Soft – Medium Soft formations Features large chisel-shaped tungsten carbide inserts to provide the highest penetration rates in the softest formations such as shales, clays, limestone and sands.
IADC CODES 437 – 517 – 527
Tricono ad Inserti IADC 435
Medium Hard – Hard formations Effective in a variety of formations with higher compressive strength such as hard limestone, sandstone, dolomite and other formations with high abrasive quality, hard streaks and broken formations.
IADC CODES 617 – 627 – 637
Tricono ad Inserti IADC 622
Hard and abrasive formations With hemispherical tungsten carbide inserts. To optimize penetration rate in hard and abrasive formations such as granites, basalts, quartzite and chert. Drilling weight of 3 ± 4 tons per inch of diameter should be applied.
IADC CODES 732 – 737 – 837
Tricono ad Inserti IADC 733
Drag Bits
Drag bits are available in both “Step” and “Chevron” configurations. Manufactured with high quality alloy steel, the blades are reinforced with tungsten carbide inserts. These bits perform best in softer, unconsolidated formations (limestone sandstone – marl). Widely used in mining, construction, exploration and water well drilling applications.
Diameter (inch)
Diameter (mm.)
Pin type
1 7/8 – 2
47.6 – 51
A-ROD
2 1/4 – 2 1/2
57-63.5
A-ROD
2 7/8 – 3
73-76
N-ROD (4 thd./Inch)
3 1/4 – 3 1/2
82.5 – 89
N-ROD
3 3/4 – 3 7/8
95-98
2 3/8 A.R.
4 – 4 1/4
101-108
2 3/8 A.R.
4 1/2 – 4 3/4
114-120
2 3/8 A.R.
5 – 5 1/8
127-130
2 3/8 A.R.
5 1/2 – 5 7/8
140-149
2 3/8 A.R.
6 – 6 1/4
152-159
2 3/8 A.R.
6 1/2 – 6 3/4
165-171
2 3/8 o 3 1/2 A.R.
7 – 7 1/4
178-184
3 1/2 A.R.
7 1/2 – 7 7/8
190-200
3 1/2 A.R.
8 1/2 – 9 7/8
216-250
3 1/2 o 4 1/2 A.R.
11 – 12 1/4
280-311
4 1/2 o 6 5/8 A.R.
14 3/4 – 17 1/2
375-445
6 5/8 A.R.
Quadrilama
Lost in the hole drag bits
Lost in the hole drag bits are meant for special jobs when the drag bit is welded or screwed in a tube of the same diameter and the drilling rig drills up to the necessary depth. When the job ends the drag bit and the tubes remain in the hole.
Replaceable drag bits
Used in a variety of formations and drilling applications, the replaceable blade feature allows flexibility in blade selection and easy replacement. Available in sizes from 3-7/8″ Chevron & Step through 5-5/8″ Chevron and 6-1/4″ Step. The total unit consists of a set of blades, head & bowl, and adaptor sub in a variety of pin sizes and options.
Blade Hole Opener
Designed to be used in soft/medium formations. It is a low cost method of fast penetration for large holes.
Jet grouting drag bits
These drag bits are meant for jobs of opening Jet Gruoting columns when cement is injected with pressures from 100-600 bars. injectors can have several sizes as 45° for horizontal jet(tunnels)m or 90° for vertical or sloping jet.
“PDC” Blade Bit
A blade bit reinforced with circular plates of synthetic polycrystalline diamond for soft/medium drilling formation, greater cut resistance, increased durability.
3 Point calipers
Tri point calipers are tools ideal for measuring Rock Bits , Hole Stabilizer ,Roller Reamers , etc.The calipers are available in 6 models that cover ranges from 80mm to 1050mm
Model Specifications
Accuracy (mm)
Measuring range (mm)
80-130
0,02 / 0,05
d.80-130
130-230
0,02 / 0,05
d.130-230
230-350
0,02 / 0,05
d.230-350
350-480
0,02 / 0,05
d.350-480
480-750
0,02 / 0,05
d.480-750
Bit gauge
Measuring and control of Bits Diameter
Availlable in 4 Models with different ranges :
Model/Range
Model 1 from 60 to 160 mm
Model 2 from 130 to 320 mm
Model 3 from 270 to 510 mm
Model 4 from 480 to 740mm.
Casing Drift mandrels
Our Drift Mandrels are precision made Instruments employed for the control of Inside Diameter of Casings,Tubings and Conductor Pipes.
Steel made, high precision machined, dimension and tollerance respect API rules (American Petroleum Institute)
We manufacture high precision Drift Mandrels and Tubing of any sizes from 2 3/8″ to 20″ and any weight.
We also may supply Drift Mandrels for Conductor Pipe until 30″
Casing Elevators
These elevators are the ideal tools for casing, screen, pump pulling and setting. They are made of bent sheets of steel, having a rugged rapid pin fastener with safety shield, stranded cable eye to eye wire rope bails.
Utilizziamo i cookie per essere sicuri che tu possa avere la migliore esperienza sul nostro sito. Se continui ad utilizzare questo sito noi assumiamo che tu ne sia felice.